Mar 03, 2010 · lo0:1: flags=2001000849 mtu 8232 index 1 inet 127.0.0.1 netmask ff000000 bge0:1: flags=1000843 mtu 1500 index 2 inet XXX.XXX.XX.XXX netmask ffffff00 broadcast XXX.XXX.XX.XXX bge0:3: flags=1000843 mtu 1500 index 2 inet XXX.XXX.XX.XXX netmask ffffff00 broadcast XXX.XXX.XX.XXX That's it! you're done. In case you want to remove the interface -
May 05, 2011 · I have net0 as my primary network interface in Solaris 11. # ifconfig net0 net0: flags=1000843
May 05, 2011 · I have net0 as my primary network interface in Solaris 11. # ifconfig net0 net0: flags=1000843 mtu 1500 index 2 inet 10.53.77.154 netmask ffffff00 broadcast 10.53.77.255 ether 0:10:e0:3a:c4:d8 Its netmask should be fffffc00, but whenever I
One comment though, the "ifconfig e1000g0 x.x.x.x netmask y.y.y.y" did not seem to work and the card was by default configured with DHCP. With a bit of searching online and several restarts later I was able to finaly get the static IP working on the card.
Host name: sap-zone2 IP address: 10.6.227.134 System part of a subnet: Yes Netmask: 255.255.255.0 Enable IPv6: No Default Route: Detect one upon reboot Inside the non-global zone, check the status of the VNIC and the status of the network service
Connect your computer to the routers WAN port with an ethernet cable and configure the IP address to 192.168.1.2 with netmask 255.255.255.0 and start the TFTP server on your computer. Now you need to connect a RS232-to- TTL cable to the serial header (do not connect VCC) as shown in the table below. Mar 03, 2010 · lo0:1: flags=2001000849 mtu 8232 index 1 inet 127.0.0.1 netmask ff000000 bge0:1: flags=1000843 mtu 1500 index 2 inet XXX.XXX.XX.XXX netmask ffffff00 broadcast XXX.XXX.XX.XXX bge0:3: flags=1000843 mtu 1500 index 2 inet XXX.XXX.XX.XXX netmask ffffff00 broadcast XXX.XXX.XX.XXX That's it! you're done. In case you want to remove the interface - Mar 12, 2019 · The hme0:1 interface is now configured, it has a default netmask of ffffff00 (255.255.255.0), and it has a broadcast address of 192.169.1.255. You could have assigned different values if you wanted to. May 05, 2014 · inet 10.158.169.10 netmask ffffff00 3. Verify the the name service is properly defined in the name service switch file (nsswitch.conf(4)) and the hostname is defined in the hosts database, e.g. hosts(4) file. iperfserv% dladm show-phys net0 LINK MEDIA STATE SPEED DUPLEX DEVICE net0 Ethernet up 1000 full igb0 iperfserv% ifconfig net0 | grep inet inet 10.129.193.63 netmask ffffff00 broadcast 10.129.193.255 iperfserv% ./iperf -v iperf version 3.0-BETA5 (28 March 2013)SunOS iperfserv 5.11 11.1 sun4v sparc sun4v iperfserv% ./iperf -s -i 1-----Server listening on 5201----- inet 129.147.11.59 netmask ffffff00 broadcast 129.147.11.255 hme0: flags=863