Aug 12, 2016 · Question from Karren: My cable modem and wireless router are sitting on a table in my living room, which is located on the first floor near the end of my house. I have a fairly large home and the Wi-Fi signal is extremely weak in a couple of the second floor bedrooms.
Jul 25, 2011 · Now before we can go any further, we have to make sure the two networks are using separate subnet ranges. If your primary router is using the 192.168.1.1-254 range, for example, then you need to make sure the second router is using a different range, such as 10.0.0.1-254. Apr 05, 2019 · Set the Internet Gateway of router 2 to router 1's IP address. Connect the two routers using a wired connection from any of port 1-4 in router 1 to any of port 1-4 in router 2. You can use a Wireless Media Bridge or Powerline Ethernet Kit to create a wired connection. DO NOT use router 2's WAN port. Press the WPS button on the wireless booster (pictured below), then the corresponding WPS button on your router (most modern routers will have one, but check before buying a booster unit). The two devices will 'talk' to each other, and your network should be extended within minutes. While 802.11ac is not available on the 2.4 GHz band, for compatibility purposes, an 802.11ac router can also serve as a Wireless-N access point. That said, all 802.11ac chips on the market support Dec 23, 2018 · If you have 2 floors, the router should be placed on the first floor’s ceiling or the second floor’s floor. If there are 3 floors, the router goes right in the middle of the second floor for best WiFi network. In other words, the router must be in a central location in order to do justice to the signal.
While 802.11ac is not available on the 2.4 GHz band, for compatibility purposes, an 802.11ac router can also serve as a Wireless-N access point. That said, all 802.11ac chips on the market support
Jan 15, 2005 · You need to have routers that support a feature called “(WDS) Wireless Distribution System”, which allows a point to point link to be established between two or more access points or WiFi routers. It's important that you don't have TWO devices on your network passing out IP Addresses. This second router will only be bridging the wireless and wired world at your house. It has no responsibilities around IP addresses. Here's an unnecessary diagram:
I have an older linksys BEFW11S4 802.11b router. I had about 5 people on it(4 wireless) for several days with no problems. My friend bought a linksys WRT54G, located about 50m away.
You can't have two superhubs or have any other connection to virgins network without having a second broadband subscription. So if you have two superhubs you can't activate that on one broadband account. If your second wireless router does not have a built in modem, (ie, it has an ethernet port for connecting to the internet). Jun 04, 2010 · The reason is that your router has 2 parts to it: 1. Modem - to communicate with the internet 2. Router - to send and receive signals to/from your pc/xbox etc. You can only use 1 modem on 1 phone line, so when you connect the 2 devices to the telephone, they cause a conflict. A great way to boost Wi-Fi signals is with the antenna on your router. If your router has only an internal antenna consider installing an external one. These have a much better ability to boost your wireless signal. A directional antenna could be the solution if you’re experiencing Wi-Fi dead zones. You can also adjust the internal antenna, too. Jul 01, 2018 · How To Connect Two Routers On One Home Network Using A Lan Cable Stock Router Netgear/TP-Link - Duration: 33:19. Richard Lloyd 2,937,675 views Jul 25, 2011 · Now before we can go any further, we have to make sure the two networks are using separate subnet ranges. If your primary router is using the 192.168.1.1-254 range, for example, then you need to make sure the second router is using a different range, such as 10.0.0.1-254. Apr 05, 2019 · Set the Internet Gateway of router 2 to router 1's IP address. Connect the two routers using a wired connection from any of port 1-4 in router 1 to any of port 1-4 in router 2. You can use a Wireless Media Bridge or Powerline Ethernet Kit to create a wired connection. DO NOT use router 2's WAN port.